聯系我們
有機硅耐熱面漆 300
關鍵詞：
有機硅耐熱面漆 300
- 產品描述
-
THERMO 300 FINISH 有機硅耐熱面漆 300
PRODUCT DESCRIPTION A heat resisting paint based on modified silicone resin and aluminium powder.
產品簡介 由改性有機硅樹脂與鋁粉組成的耐熱涂料。RECOMMENDED USE For long-term protection of hot pipelines, exhaust pipes, smoke stacks and other hot surfaces at temperatures up to 300℃ and 350℃ at a short time.
用途 長效保護溫度高達300℃（瞬時溫度350℃）的熱管道、排氣管、煙囪和其它熱表面。FEATURES Excellent heat resistance (Up to 300℃)
產品特性 極好的耐熱性（到300℃）
Good weathering resistance
極好的耐候性
Good applicability
極好的施工性能PHYSICALPROPERTIES
基本數據Color Silver
顏色 銀色
Finish Gloss
光澤 有光
Volume Solids
體積固體份 25%
Flash Point Greater than 27℃
閃點 27℃以上
Film thickness Dry : 20-30 microns/coat Wet :80-120microns/coat
涂裝膜厚 干膜: 20-30 微米/道 濕膜:80-120 微米/道
Theoretical Coverage 0.082kg/m2/20microns
理論涂布率 0.082 千克/平方米/20 微米Practical coverage depending on surface conditions, environment, applications, etc.
實際涂布率與表面處理, 外界環境, 施工方法等多種因素有關。APPLICATION
施工
Application Temperature
施工溫度 -5℃-40℃
Mixing Mix thoroughly with power agitator
混合 使用動力工具攪拌均勻
Mixing Ratio One component coating
混合比例 單組份涂料
ApplicationMethods Airless spray, air spray, brush and roller
施工方法 無氣噴涂、空氣噴涂、刷涂、滾涂Airless spray 無氣噴涂
Nozzle tip 噴嘴尺寸0.33mm-0.43mm
Nozzle pressure 出口壓力≥10Mpa
Thinning ratio 稀釋比率0-5% by weight（重量比）Brush/Roller 刷涂、滾涂
Thinning ratio 稀釋比率0-5% by weight（重量比）Thinner Paint Thinner X
稀釋劑 稀釋劑X
Drying time & Temperature 溫度5℃ 20℃ 30℃
Overcoating interval Surface dry 指觸干燥3hrs 1hr 1hr干燥時間&涂裝間隔 Touch dry 半硬干燥5hrs 3hrs 3hrs
Min. interval 最小涂裝間隔16hrs 12hrs 8hrs
Max. interval 最大涂裝間隔
Full cure: must bake in 200℃-250℃ for 1hr
完全固化：必須在200℃~250℃烘烤1 小時Typical undercoat THERMO 300 PRIMER, SD ZINC PRIMER 2000
適用下涂 有機硅耐熱底漆300，無機富鋅底漆2000
Typical topcoat
適用上涂STORAGE Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept tightly closed.
貯存于干燥陰涼的環境中，遠離熱源及火源。包裝桶必須保持封閉。
Shelf life 12months from date of production (25℃)
貯存期限 自生產之日起12 個月（25℃）
DISCLAIMER 提請注意
The information given on this sheet is to the best of our knowledge and accurate at the time of issuing. Since conditions of use are beyond the manufacturer’s control,information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
本說明書所提供信息均為目前我方所掌握最全面正確的資料,鑒于產品使用條件非我方所能控制，此中信息不含擔保，即僅在選取產品上對買方負責。由于我公司產品及生產工藝的不斷發展，本說明書的內容也會隨時進行更改，此中所有信息均以我方確認為主。產品使用前，請確認所持說明書為最新版本。www.kansai.com.cn
產品詢價
聯系方式
